What 177 owners told NHTSA about the 2019 BMW X5

I always service and baby my vehicle. Had recently got starter recall & fresh oil change done 2 months at my local BMW Atlantic City NJ dealership. On June 27th, as I was driving the vehicle normally a message popped on the dash stating engine oil is at a minimum level, add 1 liter of engine oil, refill oil immediately. So I went to my earliest autozone bought quart of mobile 1 oil and refilled it. After that the warning message went away and came felt fine. Unfortunately the next day same message popped up, so drove over to BMW service to get diagnosed. Due to the computer system in the vehicle not being able to read the oil level measurement. It would go from 0-18% oil level reading then message would pop up saying unable to read to try again or make sure vehicle is on ground level which I made sure it was. So next day I dropped it off at BMW dealership for diagnosing. After 1 day and half they came to the conclusion that it is a bad oil pump and wants to charge $6,362.31 for repairs. Advisor stated its due to older gen bmw b58 engines using plastic oil pumps inside which causes to break and cause leaks. So they are aware its an common issue but won’t do an recall or service bulletin to fix issue which is very dangerous because the engine could seize up and stall anytime I’m driving around due to not knowing the oil level measurements. It is super risky and unfair for consumers to pay for such a big bill repair. I hope there is recalls or something to help remedy this cause for current & future BMW affected vehicles. BMW is aware of this issue but won’t resolve it.

NHTSA ODI 11748220

* Intelligent Braking system. * yes it is available for inspection * I was inches from colliding with the vehicle in front of me when my car finally stopped. * Yes local official BMW dealership inspected and diagnosed the IBS module is defective. * there was no prior warning.

NHTSA ODI 11747866

The vehicle is at A&L Motors in Monroeville Pa. The vehicle has suffered a catastrophic, cascading electrical failure caused by a known manufacturing defect in the roof antenna seal. Rainwater entered the vehicle through the defective shark fin antenna seal and flooded the Telematics Control Unit(TCU). Because the TCU communicates directly with the main iDrive head unit via the vehicle's MOST/bus central data network, the water-damaged TCU short-circuited and flooded the network with corrupt electrical data, hard-bricking the iDrive system. A dealership engineer confirmed that water did not physically touch the head unit, eliminating user-error fluid spills. This cascading electrical failure has completely disabled vital safety systems, including the backup camera, forward collision driver-assist radar warnings, blind-spot monitoring alerts, and critical dashboard diagnostic notifications, creating an immediate highway safety hazard. Simultaneously, the active grille shutters (active air flaps) failed due to a defective internal actuator motor, creating a severe risk of sudden engine overheating and thermal shutdown. This component is under a 150K mile manufacturer warranty extension(SIB01 12 19 and later sib01 03 25). BMW of North America Claims Manager Joe 1-800-831-1117Ext1427 has issued an arbitrary final denial for these repairs based on a hearsay rock wedged/strike despite no apparent physical damage and zero photographic evidence. BMW is actively evading its extended warranty obligations for the air dam and a pending class-action settlement framework (Craft v. BMW NA) on the IDrive components. Additionally, this vehicle is actively subject to the critical BMW Starter Motor Overheating Fire Risk Recall NHTSA Campaign No.25V644/26V056. The dealership is unable to complete this urgent fire-safety remedy due to the same bricked Idrive unit. Grounding an owner in an un-safe car with a bricked safety display and an outstanding unremedied recall

NHTSA ODI 11746709

Oil pump with plastic parts failing

NHTSA ODI 11745369

The engine oil pump failed internally. The vehicle is equipped with a factory-installed variable-displacement oil pump that utilizes an internal thermoplastic adjusting ring. Due to heat cycles and mechanical stress, this plastic component degrades, becomes brittle, and catastrophically shatters or cracks.The first symptom appeared when the vehicle became entirely unable to complete an electronic engine oil level measurement via the iDrive system, consistently freezing and aborting the test at approximately 15% to 20%. This defect directly compromises road safety. A sudden drop in oil pressure causes severe internal engine friction, leading to immediate engine seizure or a total loss of motive power without adequate warning. Experiencing a sudden engine stall while driving at highway speeds places the driver, passengers, and surrounding motorists at extreme risk of a high-speed rear-end collision. Furthermore, a total engine shutdown disables power-assist steering and braking, making the vehicle incredibly difficult to control and maneuver to safety. Catastrophic mechanical failure from oil starvation also presents a severe under-hood fire hazard if oil leaks onto hot exhaust components.The problem has been officially reproduced and confirmed. The vehicle was brought to Bavarian Werkstatte, where certified technicians diagnosed the issue as an internal structural failure of the variable-displacement oil pump's plastic adjusting ring. The component is currently available for inspection upon request. BMW is fully aware of this defective design. They updated this exact component in mid-2020 to an all-metal oil pump to prevent plastic fragmentation. Despite knowing that the 2019 thermoplastic rings degrade, become brittle, and shatter under normal operating heat cycles, the manufacturer has failed to issue a safety recall in the United States, leaving drivers exposed to dangerous sudden engine failure.

NHTSA ODI 11741535

I am writing regarding my BMW X5 xDrive40i, model year 2019, engine code B58TU. The vehicle has been serviced at authorized BMW dealerships. For this engine type B58TU especially years 2018-2021, repeated oil pump failures have been reported due to a known design issue: an internal plastic component can develop cracks, potentially leading to a complete oil pump failure. BMW silently replaced the oil pump with the updated version by keeping the same part number but featuring metal internals. Once there is a fail on the oil pumps with plastic components, engine loses access to get the oil an immediate stop is needed. This creates a huge safety concern cause: 1) If you are on a highway at highway speeds it might not be possible to move to the shoulder safely with no engine power or even worse: with a locked engine. 2) If there is a maintenance on the road with no shoulder access or if this is a bridge where there is no shoulder, it creates a huge risk to safely move the vehicle. An unavoidable sudden stop can create a huge accident risk for everybody. Of course any car can get a engine problem on those occasions but this is a very known and very common problem for BMW cars equipped with B58TU engine especially years 2018-2021. BMW is also definitely aware of that and this safety concern cause they updated the design silently. But, when contacted with BMW NA, they refused to help, refused to admit there is a design problem. They also refused to change the oil pump with the updated oil pump even with my proposal of goodwill pricing.

NHTSA ODI 11740999

I am writing regarding my BMW X5 xDrive40i, model year 2019. For this G05 model coded cars, repeated transfer case failures have been reported due to a known issue: on the factory they put a wrong oil in it and then published a Technical Bulletin about it as if they are not the ones responsible for that. The problem is, due to that mistake, transfer cases of cars manufactured between 2018-2020 becomes dead in time. Cars shudders, jerking at low speeds, cannot deliver the power to the ground effectively due to intermittent and very disturbing, powerful shudders. This creates a huge safety concern cause: 1) if you are on an intersection the car might not join safely to the traffic in a perceived timing due to the shudders, intermittent power delivery. 2) If you are on a driveway and moving to the street the car might not move to the street for the perceived timing or once moved cannot move safely to join the traffic. 3) If there is a failure on the transfer case and if there is a sudden stop is needed. On the road with no shoulder access or if this is a bridge where there is no shoulder, it creates a huge risk to safely move the vehicle. An unavoidable sudden stop can create a huge accident risk for everybody. This is a very known and very common problem for BMW cars equipped with B58TU engine especially years 2018-2020. BMW is also definitely aware of that and this safety concern but instead of fixing it they moved away their responsibility as if they are not the ones made the mistake. But, when contacted with BMW NA, they refused to help.

NHTSA ODI 11741002

The evaporator for the air conditioning failed. BMW used an aluminum evaporator with yf coolant. Those combined cause the coolant to eat away the evaporator. Once the yf comes in contact to the air it turns toxic. This shouldn't fail at 82,000 miles.

NHTSA ODI 11739341

I am reporting a safety concern involving BMW vehicles equipped with the B58 Technical Update (B58TU) engine, commonly found in model years 2019–2021. These vehicles utilize a variable-displacement engine oil pump containing an internal thermoplastic adjusting component responsible for regulating oil pressure. Field failures are increasingly being reported in which this internal component fractures, resulting in sudden loss or instability of engine oil pressure. The failure frequently occurs during cold-start operation in low ambient temperatures. When the component fails, oil pressure regulation becomes erratic or is lost entirely. In many cases, drivers receive little or no actionable warning prior to engine damage or vehicle disablement. Reported precursor symptoms include inability to electronically measure engine oil level, abnormal oil pressure behavior, or sudden drivetrain malfunction warnings. Failures may rapidly progress to engine shutdown or severe mechanical damage caused by oil starvation. Loss of lubrication can cause the vehicle to become disabled without warning while driving or shortly after startup. This creates a safety hazard, particularly when vehicles become immobilized in active traffic or during winter conditions the cold is when they fail the most, where occupants may be exposed to freezing temperatures while awaiting assistance. Replacement of the oil pump requires extensive disassembly of the vehicle and repairs commonly exceed $6,000–$8,000 for just the pump, assuming the motor is unharmed. Owners are currently unable to determine whether their vehicles contain the original thermoplastic oil pump design or a later revised version utilizing metal internal components, as VIN-based parts information now identifies updated components in the car even when no replacement has occurred and the old components are actually in the car. Also, BMW has actively removed the plastic part number out of all dealer networks as well.

NHTSA ODI 11738531

I am reporting a safety concern involving BMW vehicles equipped with the B58 Technical Update (B58TU) engine, commonly found in model years 2019–2021. These vehicles utilize a variable-displacement engine oil pump containing an internal thermoplastic adjusting component responsible for regulating oil pressure. Field failures are increasingly being reported in which this internal component fractures, resulting in sudden loss or instability of engine oil pressure. The failure frequently occurs during cold-start operation in low ambient temperatures. When the component fails, oil pressure regulation becomes erratic or is lost entirely. In many cases, drivers receive little or no actionable warning prior to engine damage or vehicle disablement. Reported precursor symptoms include inability to electronically measure engine oil level, abnormal oil pressure behavior, or sudden drivetrain malfunction warnings. Failures may rapidly progress to engine shutdown or severe mechanical damage caused by oil starvation. Loss of lubrication can cause the vehicle to become disabled without warning while driving or shortly after startup. This creates a safety hazard, particularly when vehicles become immobilized in active traffic or during winter conditions the cold is when they fail the most, where occupants may be exposed to freezing temperatures while awaiting assistance. Replacement of the oil pump requires extensive disassembly of the vehicle and repairs commonly exceed $6,000–$8,000 for just the pump, assuming the motor is unharmed. Failures have been reported across multiple production years, and affected vehicle population boundaries remain unclear. Because this condition can result in sudden vehicle disablement without adequate warning especially in the cold, I believe this issue warrants investigation as a potential safety-related defect.

NHTSA ODI 11737203

1 - Parking Brake inoperative - Unable to disengage parking brake: Recalled part for same year/make/model (Different production MONTH in recall) NHTSA safety recall OMB Control No: 2127-0004 2 - Air conditioner (Evaporator failure) - Releasing chemicals from enclosed HVAC system: Common knowledge failure point, requires entire dashboard disassembly w/High Labor cost Unsafe driving conditions in excessive heat (Las Vegas, local area driven) History: August 2025 - Parking brake stopped working: I obtained a diagnosis from independent service shop stating the center console control panel - containing the Body Domain Controller (BDC) requires replacement. The parking brake is currently inoperable Under NHTSA safety recall OMB Control No: 2127-0004 - Part 573 Safety Recall Report 18V-732: This specific part for this specific vehicle (year, make and model) has been recalled under a different production month. March 2026 - Air Conditioner Failure: The A/C system stopped working (Blowing hot air only). I filled the A/C system on 3/12/2026, and within 2 weeks the system chemicals had been released into the environment due to a leak in the evaporator. The evaporator was diagnosed by two (2) independent mechanics as the failure point of the AC system. The Air conditioner is currently inoperable and I reside in Las Vegas - Temperatures average well over 100 degrees and we are approaching summer. Common knowledge failure point: A/C Evaporator - Located deep within the dashboard at the firewall, requiring an interior disassembly - Skilled labor and time Manufacturer's defect: Upon research, these are very common failure point as a result of the improper engineering of the AC system on this particular vehicle.

NHTSA ODI 11737457

I am reporting a safety concern involving a 2019 BMW X5 that experienced a sudden and catastrophic engine failure at approximately 75,000–80,000 miles. The failure occurred without any prior warning indicators, dashboard alerts, or fault codes. The vehicle lost engine function and required inspection by an authorized BMW dealership. The dealership documented internal engine damage, including metallic debris in the oil system, oil contamination, and bottom-end engine knocking. A full engine replacement was recommended. This raises safety concerns because: The failure occurred without warning Sudden engine failure could create hazardous driving conditions depending on speed and location There may be a broader pattern of similar failures BMW of North America has denied assistance and has not provided any explanation for the cause of the failure. I am submitting this complaint so the incident can be recorded and evaluated as part of any potential defect investigation.

NHTSA ODI 11734974

During the last service at the dealership. While they are replacing the battery, they found a melted bolt on the auxiliary battery that causes a loose cable connection and informed me that its a fire hazard. The car has 85k at the moment and all services were done at the dealership. No incident or any repairs. This is not a wear and tear. How can a bolt just melt. It might even melted a while ago and putting drivers in hazard without know because they would not noticed this unless a battery is getting replaced.

NHTSA ODI 11734301

My daughter was driving my BMW X5, it went to neutral and not moving, she was panicked and stopped the car and ignition. After restarting the car, it worked for a day, then it happened again, also, I see notifications on dashboard for restraint warning, saying, airbag, and seat belt tension are reduced. I took to Fairfax BMW in VA, BMW quoted $2662, informed that my BMW went out of extended warranty over a month, I asked Goodwill request to BMW, still declined.

NHTSA ODI 11733217

I recently took my 2019 X5 to the BMW dealership because of the recall (Engine starter) and the code P0456 (NVLD Minor Leak Fault). At the same time, there's a warning that says, "Oil at a minimum level. Add 1 liter immediately". I have the 3 Year Oil Plan and asked them to put some oil, but the dealership said that they can't add oil because the oil level wouldn’t read properly. They told me they couldn’t diagnose it without charging me an extra 300 for further testing. Then, I read a lot of threads online and it seems that BMW quietly changed the pump to an all-metal design around 2020 but never issued a recall or extended warranty for the earlier cars. There's a lot of customers complaining with the B58TU engine found in many 2019–2021 BMWs (X5 xDrive40i, 540i, 340i, etc.). The variable oil pump uses a plastic internal adjusting ring that cracks over time. When it fails, oil pressure becomes unstable or is lost, often with little warning. A common early symptom is the oil level sensor test failing and stopping around 12-20%. In the worst cases, it can lead to sudden engine damage or the car shutting down while driving. I called up my mechanic, and he said that this is a common problem and it could be an oil pump issue that needs to be replaced. I asked him for a quote and he said approximately 5k or more. I believe this is a safety defect that deserves investigation Hoping for your kind consideration. I plan to keep my car as long as possible Thanks, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ODI 11731189

Emergency call system malfunction. Vehicle available for inspection. Warning appears and verified by dealer as common issue with vehicle type due to shark fin antenna seal leaks, causing corrosion in the module when in contact with water (including rain). Cause loss of GPS and wireless capability.

NHTSA ODI 11731238

The starter on my BMW failed, and it overheated and damaged my alternator to the point that I needed to replace it. The dealer and independent service center confirmed that this was the cause, but BMW is refusing to reimburse the cost of the alternator replacement. I was at the exit of a highway and could not even put the car in neutral, so my safety was significantly at risk.

NHTSA ODI 11730444

The contact owns a 2019 BMW X5. The contact stated that while driving at an undisclosed speed, the vehicle unexpectedly overheated, and the engine temperature warning light illuminated. The vehicle was taken to a dealer, where it was diagnosed that the coolant line to the cylinder had failed and needed to be replaced. The vehicle was repaired. The contact later received notification of NHTSA Campaign Number: 25V644 (Electrical System). The manufacturer was not made aware of the failure. The approximate failure mileage was 101,187.

NHTSA ODI 11730119

The AC evaporator failed due to a known manufacturing defect common across the BMW G-chassis platform (G05, G07, G30). This has created two severe safety hazards: The refrigerant leak causes the windshield to fog up instantly and unexpectedly while driving, completely obstructing my visibility and nearly causing an accident. Chemical fumes and oil from the leaking evaporator are entering the cabin through the vents, causing dizziness and respiratory irritation for the occupants. BMW is aware of this systemic issue through numerous owner reports and petitions but refuses to issue a recall or provide assistance. This is a critical component failure that directly impacts vehicle safety and occupant health.

NHTSA ODI 11729636

I am writing to report a significant safety issue associated with BMW vehicles equipped with the B58TU engine, particularly the 2019-2021 models. These vehicles feature an oil pump containing an internal plastic component responsible for regulating oil pressure. There have been numerous instances of this part fracturing in the field, leading to a sudden loss of oil pressure. The failure predominantly occurs during cold starts in low temperatures. When this occurs, oil pressure can fluctuate erratically or be lost completely, often with minimal warning. Potential warning signs include difficulties in electronically measuring the oil level, abnormal oil pressure readings, or sudden drivetrain malfunction alerts. These issues can escalate quickly, resulting in engine shutdown or severe damage due to oil starvation. This situation poses a serious risk, as the vehicle may become inoperable without warning while driving or immediately after startup. Such failures are particularly hazardous when vehicles become immobilized in traffic or during winter conditions, leaving occupants vulnerable to harsh temperatures while awaiting roadside assistance. The replacement of the oil pump necessitates extensive disassembly and typically incurs a cost of $6,000-$8,000, assuming no engine damage has occurred. A significant concern is that owners cannot easily ascertain whether their vehicle is equipped with the original plastic pump or a revised metal component. BMW's VIN-based parts lookup now indicates updated components even if the original plastic parts are still installed. Additionally, the original plastic part number has been removed from dealer networks. Failures have been reported across multiple production years, and the full extent of affected vehicles remains uncertain. Given that this condition can lead to abrupt vehicle disablement without adequate warning—especially in cold weather—this situation warrants investigation as a potential safety-related defect.

NHTSA ODI 11721327

I bought the car from the dealership, and they said there were no problems with it, but they cheated me. The car broke down twice. The first time, it was parked in a private lot for several hours, and I paid a large sum for parking. The second time, it broke down on the street, and I waited eight hours for help to tow it back to the dealership. 1-recall message 2- emergency call system

NHTSA ODI 11719614

Subject: 2019 BMW X5 xDrive40i – Oil Pump Defect Causing Oil Measurement Failure and Safety Risk I am reporting a safety defect in my 2019 BMW X5 xDrive40i with the 3.0L B58 inline-6 engine. The vehicle currently has approximately 70,000 miles. The vehicle is unable to properly measure or display engine oil level due to incorrect oil readings, which have been attributed to a failing oil pump assembly containing internal plastic components. Because this vehicle does not have a traditional dipstick, the electronic oil level monitoring system is the only way to verify proper oil level. Due to the defective oil pump design, I am unable to confirm whether the engine has sufficient oil. This creates a serious safety concern because: •The vehicle may be operating with low oil pressure without accurate warning •Sudden oil pressure loss could cause engine shutdown while driving •Loss of power at highway speeds could result in an accident •Catastrophic engine failure could occur without proper oil monitoring This is not normal wear and tear. BMW has reportedly updated the oil pump design in newer model years to use metal internal components, suggesting awareness of a design weakness. However, no recall has been issued for 2019 models. An oil pump that prevents accurate oil level measurement and may fail prematurely presents a significant safety hazard. I respectfully request that this defect be formally investigated and that BMW be required to issue a recall to replace the defective oil pump assembly with the updated metal design.

NHTSA ODI 11718348

The contact owns a 2019 BMW X5. The contact stated that while driving approximately 45 MPH, the red oil light suddenly illuminated and the messages "Stop Carefully and Turn Off Engine", “Engine Oil Pressure Too Low", "Continued Driving will Result in Engine Damage". The vehicle was towed to the local mechanic, who discovered that the engine oil was black and thick. The vehicle was later towed to the local dealer, who confirmed that the engine oil was thick and dark, and the engine needed to be replaced. The failure mileage was 85,000.

NHTSA ODI 11716801

BMW knowingly did NOT NOTIFY it's 2019 BMW X5 M40i (engine B58) vehicle owners. This is in reference to the faulty design and made plastic engine oil pump. It has been known to fail prematurely due to weaken parts. Some analysis done was from certain oil viscosity's applying additional unneeded stressful pressures. This later was recognized by BMW and a newer design and/or metal sturdier one had taken it's place in subsequent model years starting in 2020. Some owners were able to remediate the oil pump failure and new replacement either covered under intact warranties, and some were covered through quieter negotiations with BMW Customer Care's authorizations. To my understanding, no recalls were made nor were any techical service bulletins (TSB) made to it's owners. I don't see how BMW can be allowed to get away with an issue of safety which could cause a catastrophic failure of the affected engine? Under the circumstances, BMW should be fully reimbursing me for the repairs here, and be glad there were NO serious injuries OR worse, DEATHS! I have been in contact with their Customer Care and nothing has been done to date.

NHTSA ODI 11715013

Premature oil pump failure. 2019 BMW x5 with only 46k miles has been diagnosed with an oil pump failure. Vehicle needed to be quickly pulled over and shut off to avoid catastrophic engine failure or engine seize. If this happens on the highway or at any speed the vehicle will lose power and be unsafe to control likely ending in an accident. This is a known Issue. BMW produced the vehicle with a flawed oil pump design that has a plastic ring around the impeller. The ring deteriorates and cracks leading to pump failure and loss of oil pressure It is only on limited models early 2019 X5. BMW redesigned with an all metal pump quietly. This issue needs to be addressed with BMW as it is unsafe for these family vehicles to be on the road with such a significant risk to its passengers and others. The failure happens with little to no warning. When contacting BMW they told me they would not consider helping with repairs. The repair for this part is upward of $8k which in turn will likely limit consumers ability to fix proactively. This is totally unacceptable and needs to be addressed by the NHTSA directly with BMW. P

NHTSA ODI 11714340